New Bits

Panasonic NCR 18650 3400mAh Lithium Ion Battery (2pcs)


Genuine Panasonic NCR 18650 3400mAh Lithium Ion Battery to suit FatShark battery holder.


Capacity (Ah): 3.4 Ah Max (3400 mAh) Min (3250 mAh)
Nominal Voltage (V): 3.6 ~ 3.7 V
Charging Voltage (V): 4.2 V
Charging Current (Ah): 1 Ah (1000 mAh)
Cut-off Voltage (V): 2.5 V
Energy (Wh): 12.2 Wh
Energy Density (Wh/L): 730 Wh/L
Max. Discharge rate (C): C Rating 2C (Recommended Max current 6.8 A)
Pulse current (Ah): (5-6 sec.): 12 Ah
Weight (g): 48 g (+/- 0.5 g)
Diameter (mm): 18.09 mm (+/- 0.3 mm)
Height (mm): 65.09 mm (+/- 0.3 mm)
Protected: No
Top (positive side): Flat top (Unprotected)
Model: NCR18650B
Made in Japan

Package Includes;

2 x Genuine Panasonic NCR18650B 3400mAh Li-Ion Flat Top Rechargeable Battery
Hard Case


Never completely discharge Li-Ion battery (below 2.5V under load).
Charge fully to 4.2V before first use.
Never use force to install (insert) Li-Ion battery.
Do not use old and new battery cells together.
Use only high-quality battery charger.
Do not expose to heat, NOT penetrate or modify.
Do not short (connect) positive (top), and negative (bottom) battery terminals (contacts).
Keep battery that is not in use in a plastic holder (or any insulating [plastic] container).
Never charge the battery over 4.25V (another reason to use high-quality battery charger).
Do not charge unattended nor overcharge.
Do not store your Li-Ion batteries fully charged (for an extended period of time).
Store in cold and dry place at approximately 3.7V (storage charge).
After the battery is discharged-don't leave it discharged=>charge it as soon as possible.
Disposal must only be at designated battery recycling depot.

List Price: $26.95
Price: $26.95
SKU: PA340018650

In Stock: Totally in stock right now

Spedix Quad Wrench with One-way Bearings


This is the handiest little prop wrench you could own. It's a small T snapper that fits comfortably in your hand and has a one wear bearing on it for easy wrenchy-like removal or tightening of your prop nuts Comes with some M3 sized little side pieces too for those other little nylon nuts you might have.

List Price: $15.00
Price: $15.00
SKU: SPX-71066

In Stock: Totally in stock right now

Futaba PWM SBUS Encoder for CGY750


This is the Futaba SBE-1 SBus PWM Adapter.

Makes almost any receiver instantly compatible with SBus programmable servos, as well as the CGY750 and other SBus-capable equipment.

Converts input from up to 10 PWM channels into a single SBus output.


PWM Input: Max 10 Channels
Input Pulse Width: 805 – 2,235μS
Input Frame Rate: 3 – 27.3mS
Output Signal: S.Bus
SBus Data Rate: 100kbps
Output Frame Rate: Approx. 7mS
Operating Voltage Range (Rated): 4.8 – 7.4V
Dimensions: 23.5×33.5×9.5mm (excluding cable)
Weight: 15g

List Price: $75.00
Price: $55.00

In Stock: Totally in stock right now

Beta65 Pro BNF 1S Brushless Drone (OSD)


There is a whole lot of crap out there when it comes to brushless micros in the whoop form factor.

We've been really particular about our decision making process in stocking brushless whoops.

The market has recently been inundated by cheap and nasty (but in reality - quite pricey), well, crap.

Traditionally brushless whoops - particularly the 'affordable' ones, had sported brushless motors that have been unreliable and underpowered, sitting on flimsy, fragile frames and driven by flight controllers just too inaccurate to enjoy that locked in feeling you need to hit those tight gaps that make whooping fun!

That is, until now!

We are happy to offer our customers the new and improved upgraded Beta65 pro brushless whoop.

Sporting 19,000kv (Yes! 19,000kv) brushless motors, with innovative new e-clip design to prevent bell fly-offs, mounted on the BEST and most durable brushless whoop frame available - the new and improved BetaFPV 65 pro frame and driven by the brand new BetaFPV F4 flight controller with integrated FrSky SPI long range receiver with OSD, telemetry AND an open UART for Smart Audio. The rock solid BetaFPV Z01 mullet AIO camera provides rock solid, low latency FPV.

All this packed in to the traditional 65mm tiny whoop ducted form factor.


Props 31mm - 1mm shaft diameter (shaft diameter is important - brushed props have a 0.8mm diameter and will need to be drilled out to 1mm to be compatible (coming very soon)

Frame BetaFPV Beta 65 Pro frame

Motors 0603

Battery Any tiny whoop "stick" style 1S battery with powerwhoop connector (260-300mah recommended)

Canopy All canopies we stock


Frame: 65pro frame
Propeller: 31mm 4-blades propellers (1mm shaft hole)
Motors: 0603 19,000KV
Fligh Controller: BETAFPV F4 1S brushless FC
Firmware version: betaflight_matekf411rx_3.4.0
ESC: 5A/6A preak BLHeli DSHOT600 ESC (integrated with FC)
Camera & VTX: Z01 25mW AIO mullet VTX camera
Battery: 260mAh Lipo HV Battery
Receiver: Built-in Frsky SPI RX
Weight: 23.29g (without battery)
Flight time: 2.5 minutes with 260mAh HV battery


The flight controller

Comparing the old F3 Brushless FC & the new F4 Brushless FC

CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
Size: 26mm x 26mm, fully compatible with the Inductrix quad frame, Beta65 Pro frame, Beta75 Pro frame, BWhoop B06 frame and mounting pattern
Firmware version: betaflight_matekf411rx_3.4.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Built in SPI Frsky D8 protocol native receiver
Power supply: 1S
ESC Current: 5A continuous and peak 6A (3 seconds)
ESC BLHeliSuite programmable
ESC Factory firmware: O_L_5_REV16_6.HEX
ESC Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 4g
What is SPI?
Basically, SPI is a communication protocol like UART, a serial communication protocol. A SPI connection requires 4 wires, while an UART connection only uses 2 (TX and RX). However SPI is faster than UART and places less stress on the processor.

Currently the built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules with International Firmware (in D8 mode). Pay attention, this is a SPI connection receiver. In Betaflight Configuration, it should be setted as FRSKY_D receiver in SPI RX mode.

The motors

The frame

The Beta65 Pro BNF sports the new and improved Beta65 Pro frame.


1 x Beta65 Pro 1S FrSky Brushless BNF micro whoop quadcopter drone
1 x BetaFPV 260mah HV battery

List Price: $160.00
Price: $160.00
SKU: 00313138

In Stock: Totally in stock right now

Beta65X 2S Whoop Quadcopter Frsky


Introducing a new era for Whoop micro drones. This 2S Whoop drone has the power to fly real acro, like a larger quad, but is still small enough, safe enough, and quiet enough to fly anywhere.

A team of well respected micro modders have teamed up with BetaFPV to produce this whoop, being involved and consulted on every single step including frame design from scratch, FC and ESC stack design, motor design and prop combinations.

A lot of time and effort by not only those running BetaFPV, but purist hobbyists, has gone in to the research and development of this quad.


High performing STM32F405 processor FC boards and tuned Betaflight Ominibus 3.5.0 firmware, the Beta65X is ready to bind and fly out of the box without requiring tedious tuning.
Durable and light enough frame is custom produced for the Beta65X. A total assembled weight of 26g gives pilots a good balance of weight and nice punch on 2S voltage.
Fully assembled — no soldering or tinkering necessary. The custom produced 17500kv 0802 motors are the lightest ever produced and replacing them is easy with simple, light-weight, plug and play connectors.
2 x 1S batteries connected in series is configured by default, making this new offering a more affordable upgrade.

Weight: 26g (without battery)
Motors: 0802 17,500KV with connector
Props: 31mm 4-blades props, 1mm shaft opening
Camera tilt angle: 35 degrees

CPU: STM32F405
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD) 3.5.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Smart Audio port is available for radio control VTX

Support BLheli/BLHELI_S suite Pass-through ready
Dshot600 in default
Input voltage: 2S lipo
Cotinuous current: 6A
Peak current: 10A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Connector: XT30 or PH2.0 series connector

The whoop comes with a custom split Z02 smart audio AIO cam/vtx by default with a custom designed mount for a 35 degree viewing angle for faster flying.

Output power: 0mW, 25mW and 200mW (switchable)
Smart Audio function is included for radio control out of the box
Antenna: Dipole
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
TV System: NTSC
Field of view: 100-120 degrees with 1/4 lens
The Beta65X drone also comes with "props out" by default. Why we need "props out" direction?

Default Betaflight props direction, quadcopter dips and "washes out" in hard corners. With reversed props or "props out", no more dipping even in hardest cornering.

There is only one choices for the Beta65X - PH 2.0. The two 260mAh Lipo HV 1S batteries can be inserted into the slot in design, as seen below.

The AIO camera VTX on the Beta75X is a customed version of Z02. The VTX board and camera board are split and 35 degree camera mount for more fast flying. At the same time, it have all the other function of the Z02 camera, like output power switchable between 0mW, 25mW and 200mW. Smart audio is available for VTX remote control in default.

1 * Beta65X BNF 2S Whoop Quadcopter
1 * Spare 31mm 4-blades props (2CW+2CCW)
2 * 260mAh 1S batteries - none included with PNP version.
1 * spare canopy

List Price: $179.00
Price: $179.00
SKU: 00313360

In Stock: Totally in stock right now

BetaFPV FC Screws and Damper pack


Those screws and rubber dampers are really useful when you are mounting flight controller board to your Blade Inductrix or Tiny Whoop Quadcopters. M1.2* 4 screws fit for stock Blade Indcutrix frame. M1.4* 5 screws fit for Eachine black E010 frame or Beta75 75mm frame.

20 * M1.2* 4 screws
20 * M1.4* 5 screws
20 * ruber dampers

List Price: $11.50
Price: $11.50
SKU: 00312960

In Stock: Totally in stock right now

BetaFPV Z02 AIO Camera 5.8G VTX


This is the pin connected version. Although realistically, you can easily just cut/de-solder the pins and replace with wires if you wanted. You'll be right. It comes with a white TPU printed mount for the camera and vtx, works nicely.

Z02 AIO camera VTX is the newest video transmitter by BETAFPV. It has 2 great improvement since. First, switchable power output between 0mW, 25mW and 200mW. Second, Smart Audio is included and pilots could control the VTX via your radio transmitter.

Switchable power includes 0mW, 25mW and 200mW.
Smart Audio function is included in this AIO Z02 camera. The flight controller can communicate with the video transmitter using the audio line in. It allows the flight controller to know what frequency the vtx is using, and to change it.
Fixed 20° tilt camera mount. At this angle the pilot can still see everything ahead in full-blown fast forward flight.
Dipole whip high sensitivity antenna

Output power: 0mW, 25mW and 200mW (Adjustable)
Supply Voltage: 2.9-5.5V
Size : 27*17*14 mm
Weight: 4.7g
Antenna: Omnidirectional ANT
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
TV System: NTSC
Field of view: 100-120 degrees with 1/4 lens.
Frequency group A~F selected still touch up to 2 secs
Channel ch1~ch8 selected with short touch.
Power switch with long touch up to 5 secs.

1 * BETAFPV Z02 FPV Camera
1 * TPU Holder
2 * Head pins (Using to connect with newest BETAFPV FC boards)

List Price: $39.95
Price: $39.95
SKU: 00313392

In Stock: Totally in stock right now

BetaFPV 0603 19000KV Brushless Motors


These motors are the stock motors for the Beta65 Pro 1S brushless drone.

Plug:Micro JST-1.25 3-pins connector
Height: 16.2mm
Width: 9mm
Weight: 1.6g ( with connector)
Shaft: φ1.0mm
KV (rpm/V): 19000KV
Voltage: 3.7-7.4V
Battery: 1S lipo battery (2S is not recommended)
Load Current: 1.8-3.8A
Pull: 23-40g
Power: 6.7-28W
Efficient: 3.4-1.4g/W
Usage: for 1S brushless multirotor like Beta65 Pro or BWhoop B06 etc

4 * BETAFPV 0603 16000KV Brushless Motors
Some M1.6x4 screws (Fit for Beta65 Pro and Beta75 Pro frame)

List Price: $58.00
Price: $58.00
SKU: 00313248

In Stock: Totally in stock right now

BetaFPV Upgraded Beta65 Pro Micro Brushless Whoop Frame


This is the upgraded and latest Brushless Whoop frame from BetaFPV.

Here's a picture showing you the differences between the previous versions:

This is designed for 0603 motors. Whilst you can run the 0703 motors if you really had to... don't do it, its inefficient and bad juju.

List Price: $6.00
Price: $6.00
SKU: 00313229

In Stock: Totally in stock right now

BetaFPV 300mAh High Voltage (HV 4.35) Lipo Battery


The new 300mah packs come in only 0.6 grams heavier than the 260mah packs. More punch and longer flight times by sacrificing a little in weight.


Cells: 1S
Voltage: High Voltage (HV) 4.35v at full charge
Connector: JST-PH 2.0 (PowerWhoop)
Rating: 30C constant, 60C peak
Dimension: 11 x 6 x 58mm
Weight: 7.5g
Capacity: 300mAh

HV LiPos, otherwise known as LiHV batteries, can be charged to either the standard 4.2 volts or the high voltage 4.35v standard - providing more power and considerably longer flight times.


The PowerWhoop connector allows for a more efficient flow of power, resulting in more power and considerably longer flight times.

List Price: $7.00
Price: $7.00
SKU: 00313295

In Stock: Totally in stock right now