New Bits

25 degree mount for VM2751 camera


$2.80

This mount is printed from semi-transparent, high-impact ABS.
It is part of our Whoop Brain kits, but you can also get it separately here.

It weighs 0.6g and is intended to mount a VM2751 camera at a 25˚ angle to a (somewhat) flat surface.
The grooves at the bottom allow for a better grip into glue.
To fix the camera onto the mount, use a 2mm zip-tie.

This mount is designed to be as crash-proof as possible. That means it will not break, and it will provide enough flex to minimize damage to the attached components.

I suggest to use "Permatex Black Adhesive Silicone" to glue the mount to the FC, as shown in this video:

The silicone forms a very flexible bond, so in the event of a crash, the mount will move and then return to its position. The zip-tie provides additional flex between camera and mount.

If you need to change/remove the camera, that's easy by snipping the zip-tie.

Removing the mount from the surface is easy as well. You just need to pull steady and hard enough, while slicing the silicon with an exacto knife. Make the cut as close as possible to the FC surface, so when you glue a new mount, you can use enough fresh glue without making it heavier than needed.

List Price: $2.80
Price: $2.80
SKU: cam-VM2751


In Stock: Totally in stock right now

BetaFPV F3 FC with OSD (FrSky)


$49.00

BetaFPV FC with F3 chip, embedded OSD and FrSky or DSM Rx (SBUS)
fits Whoop frames with 26x26mm mounting pattern

This flight controller is part of our Whoop kits.
To use the on-screen-display, use the VM2751 cam/vTx.

build instructions:

specifications:
CPU: STM32F303CCT6
sensor unit: MPU6000
ESC: 6.3A rated MOSFETs
dimensions: 26mm x 26mm
OSD: integrated BetaFlight OSD
receiver: Frsky D8 or DSM (SBUS)
power Cable: 55mm, with JST-PH 2.0 connector
weight: 3.4g

binding: press button on FC, then apply power. Now put transmitter into bind mode. Wait a few seconds, exit bind mode on Tx, then power cycle the FC.

The FC comes pre-flashed with BF 3.1.7. I recommend to update your board to the latest stable version BetaFlight 3.2. Here is a video about flashing and configuring BetaFlight:

List Price: $62.00
Price: $49.00
SKU: Beta-F3-Fr


In Stock: Totally in stock right now

Tiny Whoover - Micro Hovercraft Kit (Black)


$14.00

Based on the idea of BadAssDrones, Drone Junkie created an extremely thought-out micro hover craft kit that uses the electronics of a micro quad as control and propulsion system.

kit contents:
2x foam sheets with body parts
2x 3D-printed motors mounts
1x bottom skid pad

required, but not included:
- whoop frame, motors, propellers (recommended: 7016 body kit)
- flight controller (any whoop FC will do, but a programmable one is best)
- batteries (anything between 200mAh and 600mAh works)

List Price: $14.00
Price: $14.00
SKU: Whoov-Body-black


In Stock: Totally in stock right now

Tiny Whoover - Micro Hovercraft Kit (Red)


$14.00

Based on the idea of BadAssDrones, Drone Junkie created an extremely thought-out micro hover craft kit that uses the electronics of a micro quad as control and propulsion system.

kit contents:
2x foam sheets with body parts
2x 3D-printed motors mounts
1x bottom skid pad

required, but not included:
- whoop frame, motors, propellers (recommended: 7016 body kit)
- flight controller (any whoop FC will do, but a programmable one is best)
- batteries (anything between 200mAh and 600mAh works)

List Price: $14.00
Price: $14.00
SKU: Whoov-Body-red


In Stock: Totally in stock right now

Tiny Whoover - Micro Hovercraft Kit (Blue)


$14.00

Based on the idea of BadAssDrones, Drone Junkie created an extremely thought-out micro hover craft kit that uses the electronics of a micro quad as control and propulsion system.

kit contents:
2x foam sheets with body parts
2x 3D-printed motors mounts
1x bottom skid pad

required, but not included:
- whoop frame, motors, propellers (recommended: 7016 body kit)
- flight controller (any whoop FC will do, but a programmable one is best)
- batteries (anything between 200mAh and 600mAh works)

List Price: $14.00
Price: $14.00
SKU: Whoov-Body-blue


In Stock: Totally in stock right now

Tiny Whoover - Micro Hovercraft Kit (Yellow)


$14.00

Based on the idea of BadAssDrones, Drone Junkie created an extremely thought-out micro hover craft kit that uses the electronics of a micro quad as control and propulsion system.

kit contents:
2x foam sheets with body parts
2x 3D-printed motors mounts
1x bottom skid pad

required, but not included:
- whoop frame, motors, propellers (recommended: 7016 body kit)
- flight controller (any whoop FC will do, but a programmable one is best)
- batteries (anything between 200mAh and 600mAh works)

List Price: $14.00
Price: $14.00
SKU: Whoov-Body-yellow


In Stock: Totally in stock right now

Spedix 4in1 Brushless ESC (6S/40A/BLHeli32)


$89.95

Look out 6s pilots, Spedix has just released there newest offering for the 6s monsters hitting the tracks and flying fields all around world. Larger MOSFETS allow for better curent handling which results in pure performance. As always, no expense was spared to bring the highest quality and best performance of any 4in1 esc on the market.

GS40A-4IN1 is designed to be the best performance and reliability in the 4-in-1 ESC domain.

To achieve the target, we use the lowest RDS standard size 5x6mm MOSFET with only 0.85mOhm resistance, making the ESC 40A capable in the real world. In contrast to the 30V MOSFET used by most competitors in the market, this 40V MOSFET improves the overall reliability in fast response to throttle signals. To meet the strict requirements in racing competition, we designed 50V power supply circuit and 5V clean output. To improve high current workload, we use high TG PCB of 6 layers even though the cost is much higher. On top of all these excellence in product designs, our engineers managed to control the dimensions to be the same as a standard 36mm flight controller board, without sacrificing the precious space in a quad.

Specs:
Input Power: 2-6s
Continuous Current: 40a
Burst Current: 45a>10s
BEC: 5v 2a
Current Detection: Yes
Firmware: BLHELI32
High Voltage MOSFETS
Telemetry and Current Protection

Includes:
GS40A 4-in-1 ESC
Cables & Wires
Soft mounting grommets

List Price: $89.95
Price: $89.95
SKU: SPX-71065-4in1


In Stock: Totally in stock right now

Eachine QX65 Micro FPV Racing Drone


$77.00

Eachine QX65 is a new upgrade Tinywhoop based on Betaflight 3.2.2 integrated Betalight OSD , support ACRO/ANGLE/AIR flight mode, it’s built-in Eachine Beecore V2.0 flight controller and 700TVL 1/4’ CMOS Camera and 5.8g 48CH 25mw VTX, the camera comes with an lens angle adjustable holder, the Booster 615 coreless motor supply much more power ,it’s a best Micro in-door FPV racing drone which include all your need’s FPV gears.

Specification:
Brand: Eachine
Item NO.: QX65
Wheelbase:65mm
Prop size: 31mm
Weight:20g (Not include the battery);
26g (Include 4.35v 250mah battery)
Battery power: 3.8v 250mah 30C
Camera: 700TVL 130degree 1/4’ CMOS
VTX:5.8G 48CH 25mw
Motor: 0615 Coreless motor with PH 2.0 plug
No-load speed: 68000 ± 10% RPM
load speed: 42000 ± 6% RPM
Frame: High quality ABS
Flight controller: Eachine Beecore V2.0

Features:
- Betaflight 3.2.2 Firmware
- F3 Flight controller Built-in Betaflight OSD
- Support ACRO/ANGLE/AIR flight mode
- Comes with four LED’s(2 red + 2white)
- Camera Lens Angle adjustable
- 0615 Booster coreless motor supply much more punch
- HV 4.35v Lipo much more power

2.4G Receiver option:
Frsky 8CH protocol D8 Mode (SBUS)
Flysky 6CH AFHDS 2A protocol (IBUS)
Spektrum DSM2/DSMX protocol

Compatible:
1.Frsky Receiver Support FRSKY X9D/X9D PLUS(D8 mode),and XJT (D8 Mode),DJT DFT DHT Transmitter.

Package Included (Basic Version):
1 x 65mm Frame
1 x Cover
4 x 31mm Propellers
1 x Eachine Beecore V2.0 flight controller(Built-in 2.4G receiver and OSD)
1 x Aio 3in1 Camera & vtx
4 x 615 coreless motor
1 x 3.8v 250mah 30C Lipo Battery
1 x 4.35v USB charger
1x Propeller disassembly tools

List Price: $89.00
Price: $77.00
SKU: ECH-QX65-BASIC


In Stock: Totally in stock right now

Quadracer God Mode 5 Inch Racing Frame 5mm Edition


$60.00

Luke Godeassi has been a long term contributor to the QuadRacer aesthetic while also being the primary tester for all race frames. His personal style of pure racing pragmatism has led to the development of the God_Mode.

Features:

2mm sandwich design
Quickchange arms
Shorter arms (less leverage)
Stretch X or Wide X interchangeable
UFL antenna support ONLY
Micro camera ONLY
Lightweight Design
Turtle Mode pod
Camera angle indicators
Spare arm included
Black press nut pre-fitted
Compatible with M8 micro cameras only.

Utilising Quickchange arms, the god_mode allows all the great race day maintenance that Nemesis facilitates.

The pod does NOT support SMA connections and as such you will need to run a UFL antenna. However, because of the design, you won't need to remove this every time you need to do major maintenance, simply cutting a cable tie will allow you to remove the antenna.

The arms themselves do not go to the centre which is a huge weight saver. Due to their shortened length as a result of being away from the main core, they are surprisingly crash resistant despite their narrow width.

It is not recommended to run individual ESCs and ideally an Asgard or similar AIO is the best configuration.

It comes with steel bolts by default allowing for a 68g dry weight.

Pod colour choice is limited, put your preference in the order comments (red, yellow, green, purple etc)

List Price: $60.00
Price: $60.00
SKU: QR-GM5IN5MM


In Stock: Sorry bro, Sold out

Lumenier AXII U.FL 5.8GHz Antenna (RHCP)


$28.95

The Lumenier U.FL AXII 5.8GHz Antenna takes all the same technology of the full size AXII and adds a U.FL connector for direct VTX connection! Lumenier, in collaboration with renowned FPV antenna designer Hugo of TrueRC, brings you the smallest, lightest and best performing FPV antennas in the world. The AXII U.FL antenna is an original design that features a new RF pathway technology (unique hybrid network) allowing it to be incredibly light weight (2g) making it the smallest and lightest 5.8GHz CP antenna.

Even though the AXII U.FL is both small and light weight, it does not sacrifice on performance. In fact it out performs most other antennas in all categories. Precision engineering has given this antenna a near perfect 1.0 Axial ratio resulting in a true circularity. On top of that, the AXII has a high max gain of 1.6dBic enabling better range and penetration. It has a wide bandwidth covering the popular FPV 5GHz band from 5.5GHz-6.0GHz, ensuring you have a clear and strong signal no matter which frequency you're on.

The AXII is designed to be ultra durable and put up with the beatings FPV pilots put on their antennas. The entire antenna array is securely protected inside the outer casing. The outer shell case is made from an impact resistant polycarbonate material, and it is sealed shut to guard the antenna elements inside.

Join the online discussion about the Lumenier AXII Antenna at RCGroups here.

Specifications

Gain: 1.6dbic
Axial ratio: 1.0 (near perfect)
Bandwidth: 5.5GHz-6.0GHz
Radiation Efficiency: 98%
SWR: <=1.5:1
Weight: 2g
Size: 15mm x 16mm
Cable Length: 60mm
Connector: U.FL
Compatible with other styles of 5.8GHz RHCP antennas

Polarization

Right Hand Circular (RHCP)

Includes

1x Lumenier U.FL AXII 5.8GHz Antennas (RHCP) with UFL connector

Videos

List Price: $28.95
Price: $28.95
SKU: LUM-AXII-RHCP-UFL


In Stock: Totally in stock right now