New Bits

CL-0617-25 Coreless Motor (speed: ludicrous) 4 Pack


The craziest motors around, not for everyone and certainly not for the feint hearted. As these are longer motors, you need to be running the cockroach frame and you need to trim the little bit of plastic at the bottom of each motor housing to fit them.


speed: 25.000Kv
operating voltage: 1.5-3.7V
current draw under full load: 3.5A

can diameter: 6mm
can length: 17mm
shaft diameter: 0.8mm
shaft length: 5mm
weight: 1.9g
wire length: 7cm
plugs: Micro-JST 1.25

List Price: $33.00
Price: $33.00
SKU: MMW-CL-0617-25

In Stock: Totally in stock right now

Rambo Whoop Kit (FrSky)


This is the Chief Scientist's special combo, the Rambo Whoop complete kit (fast spec)

- NewbeeDrone Cockroach frame
- NewbeeDroneBeeBrain FC (FrSky)
- PH2 pigtail
- VM275T camera/vTx
- 20˚ camera mount
- 4 propeller (1 set)
- 4x 205mah batteries

recommended tools/parts for assembly:
- soldering iron with fine tip
- solder and flux
- SMD hot air gun (to melt keratin)
- very small philips screw driver
- wire cutter/stripper
- 2mm zip-tie (to fix cam to mount)
- keratin glue, the soft variety (similar to hot glue, but better)
- glue-lined 6mm heat shrink (to protect antenna joint)
- 3rd hand (e.g.

FC preparation:
- flash FC with BF 3.0.1
- copy Dr. Whoop inverted settings dump into CLI
- bind receiver, test input channels, set modes

solder work:
- remove power connector from FC
- pre-tin power pads on FC
- solder pigtail to FC
- solder vTx to FC

final assembly:
- zip-tie cam to mount
- glue mount to FC
- glue antenna to frame

Betaflight 3.0.1. CLI dump:
(note: due to bugs in the "modern" PID controller in Betaflight, we are using the legacy PID controller that was part of BF 3.0.1 and earlier. You *need* to flash BF 3.0.1 before using these setting dumps to configure your FC!)

- setting dump inverted (plugs facing up, as in the video)
- setting dump stockish (plugs facing down)

List Price: $165.00
Price: $165.00

In Stock: Sorry bro, Sold out

Spedix GS35 Brushless ESC (2-6S/35A/BLHeli32)


Here it is, the Latest 32 Bit ESC from Spedix is here with 2-6s voltage input!

Smallest 35A 32 bit 2-6S ESC in the market
Uses 40V MOSFET, compared with 30V brands - Gives more redundancy
Uses 10 capacitors, much more than competing brands
telemetry port and current protection supported
Based on our ES30HV, the most reliable ESC in the market

List Price: $21.00
Price: $19.50
SKU: SPX-71043

In Stock: Totally in stock right now

FatShark Dominator V3 Headset


These video goggles allow for first-person viewing (FPV) of the video downlink from the wireless transmitter on your RC aircraft for a truly immersive flying experience.

The FatShark Dominator V3 headset focuses on HDMI connectivity with 720p support through a robust mini HDMI port and 16:9 format WVGA image. An improved DVR can swap between NTSC and PAL format as well as power backup to write files should the power be disconnected while recording. The Dominator V3 has modular bays to support 1G3, 2G4 and 5G8 band receivers and ability to add the Trinity head tracker.

The FatShark Dominator V3 headset features a modular design, meaning that additional modules and accessories can be added for expandable functionality. In order to receive the video downlink from your wireless video transmitter, a receiver module is required. Receiver modules are available in 1.3GHz, 2.4GHz, or 5.8GHz options. Please note that Fat Shark only guarantees compatibility with NexwaveRF modules from Fat Shark for ImmersionRC. To install the receiver module, simply remove the door panel on the side of the headset, insert the module, and snap the door panel back in place.

For the most immersive experience, the optional 3-Axis Trinity Head Tracker module can be inserted into a slot on the opposite side of the headset, accessed through a second removable door panel. The head tracker lets you control pan, tilt, and roll of your aircraft-mounted FPV camera (sold separately) using the motion of the headset.

Also includes the new FatShark fog-e-nator faceplate, which not only provides superior comfort, but also a fan to prevent foggy goggles (foggles) on cold days and air con for sweaty eye balls on hot days.

Power is provided to the headset using the new 1800mAh battery which securely fits in a head strap pocket on the headset. Also included with the headset is a DC power cable, AV cable, and carrying case.

Included Accessories;
AV cable
HDMI cable with mini to micro and mini to standard adapters
1800 mAh battery with LED indicator (note middle wire removed to prevent balance charging)
charge cable adapter
Zipper carry case

FOV 30°Diagonal
59-69mm IPD Range (adjustable)
WVGA 800 X 480 Display
Support Side/Side 3D
NTSC/PAL Auto Selecting
HDMI 720p Support
Integrated Analog DVR (no HDMI recording)
Modular Head Tracker Bay
Modular Receiver Bay
DC in: 7-13V (2S/3S)
Power Consumption: 3.6W

Optional Accessories; (Receiver module is not included, sold separately)
5.8GHz Fat Shark with Raceband, 1G3 Fat Shark, 2.4GHz Fat Shark
Optional diopter lens inserts: -2, -4, -6 dpt sold separately
Trinity 3 axis head tracker module
43 channel RF Module support over 6 bands (1.3, 2.4, 5.8 Ghz)
Please Note:

Exposing the lens to direct light sources will result in LCD damage.
Battery included requires a lipo charger capable of 2s and 1.8A max (standard charge non balancing as battery has an internal charging circuit) new batteries have the middle wire removed to prevent this.

Manual for FatShark Dominator V3 headset

List Price: $539.95
Price: $470.00
SKU: FSV1063

In Stock: Sorry bro, Sold out

CL-0716-17 Coreless Motor (speed: insane) 4 Pack



speed: 17.000Kv
operating voltage: 1.5-3.7V
lifetime rating: 5-6 hours


can diameter: 7mm
can length: 16mm
shaft diameter: 0.8mm
shaft length: 5mm
weight: 2.9g
wire length: 8cm
plugs: Micro-JST 1.25

List Price: $33.00
Price: $33.00
SKU: MMW-CL-0716-17

In Stock: Totally in stock right now

JST-PH-2.0 4 Way Parallel Charge Cable


Charge 4 single-cell lipo batteries at once - with a regular hobby charger.
Fits the 205mAh packs with PH2 connector.

This adapter is made with the finest ingredients and with great attention to detail. The best plugs, the thickest wire, and a high quality silicon coating.

- plug cable into charger
- connect 4 discharged batteries
- charge at 1S voltage and combined 1C current

For 4x 205mah batteries, the combined capacity is 820mah, so a 1C charge rate would be 0.82A. You can charge these packs with up to 2C (1.64A), but to maximise life time, 1C is better.

List Price: $9.00
Price: $9.00

In Stock: Totally in stock right now

Mylipo HV 255mAh 25C 1S Battery (PH2)


The HV 255mah/25C pack from


cell count: 1
nominal voltage: 3.8V
maximum voltage: 4.35V
capacity: 255mAh at 4.2V, 265mah @ 4.35V
continuous discharge rating: 25C
dimensions (incl. plug): 71mm x 11mm x 5.5mm
weight: 6.8g
plug: JST-PH-2.0

List Price: $10.50
Price: $10.50
SKU: MMW-ML-HV-255-25-1-PH2

In Stock: Sorry bro, Sold out

Mylipo HV 205mAh 25C 1S Battery (PH2)


The 205mah/25C LiHV pack from,
The "Jesse Perkins edition" - with a larger plug AND higher voltage!


cell count: 1
nominal voltage: 3.8V
maximum voltage: 4.35V
capacity: 205mAh at 4.2V, 230mah @ 4.35V
continuous discharge rating: 25C
dimensions: 51mm x 11mm x 5.5mm
weight: 5.5g
plug: JST-PH-2.0
May the punch be with you!

List Price: $8.50
Price: $8.50
SKU: MMW-ML-HV-205-25-1-PH2

In Stock: Sorry bro, Sold out

IBCrazy 5.8 GHz Biquad Linear Antenna


VAS Video Aerial Systems 5.8GHz BIQUAD 11dbic Antenna

List Price: $35.00
Price: $35.00
SKU: VAS-BQ-5800

In Stock: Totally in stock right now

IBCrazy Genesis Linear 5G HD ARRAY Prosight Antenna Upgrade Combo Set


The HD Linear Upgrade Combo Set is a Genesis Array paired with our HD Transmitter antenna set. If you are looking to upgrade both sides of your 5G HD system (ie-Connex Prosight) for the first time or you simply want the ease of ordering a single item, the HD Upgrade Combo is for you.

What's Included:

The Genesis is an 11dbi Linear Array designed for today's modern 5Ghz band High Definition FPV systems. This single panel array houses five Vertically polarized Linear antennas with a 115 degree beamwidth. Don’t let that fool you though, we have flown over 1000ft behind this array. All five antennas are manufactured on MilSpec RG-316 cable for durability and terminated with an RP-SMA connector for perfect integration with today’s Digital systems. A custom 316 stainless steel bracket for mounting the array with a Connex receiver together on a tripod via the standard ¼-20 bolt is also included. If you are looking to push range limits on 5Ghz band based High Definition systems, the Genesis should be your first choice.

Gain: 11dbi
Beam width: 115 degrees
-3db point: 55 degrees

Frequency Range: 5100mhz-6200mhz
Polarization: Linear (Vertical)

When looking for an upgrade to your 5G HD system's fragile PCB board antenna, look no further. The VAS HD Dipole is designed as a durable replacement to those PCB antennas that are detuned by any material they are placed in contact with and require awkward mounting solutions. Not only are they durable, but they are balanced specifically to counteract the issues placed on antenna systems by poor installation practices. We have incorporated not one, but two baluns to ensure the best possible transmission from vehicle to ground station. While it may appear to be a humble sleeve/bazooka style dipole, it is far from it.

We have also included MMCX to SMA extensions to allow you flexibility in installations. You are not limited to mounting these in awkward positions on your vehicle.

Gain: 2.05dbi

Frequency Range: 5100mhz-6200mhz
Polarization: Linear

Package includes: 1- Genesis Linear Receiver Array, 1- Stainless Steel Mounting Bracket and 1 Pair- HD Linear Transmit antennas w/MMCX to SMA Cable

Part Number: HDCOMBO-LIN

List Price: $129.00
Price: $110.95

In Stock: Totally in stock right now