Product Search

BetaFPV 31mm 4-blade Micro Whoop Propellers (1.0mm Shaft) Blue


Experienced pilots will have different preferences when it comes to the number of blades on whoop drone propellers.

However, the general consensus is that 4-blade props produce greater thrust at a small efficiency expense — making them perfect for those looking for that extra edge when racing.

These props are suitable for the brushless tiny micro quadcopter whoops and and fit the shafts of BetaFPV's 0603, 0703 and 0705 motors.

These props will not work with our coreless brushed motors - the shaft diameter opening is too large and props will not be securely affixed to those motors.

THE IMPORTANT STUFF

Product material: Plastic
Outer diameter: 31mm
Shaft diameter: 1mm
Height: 7.2mm
Weight (2CW+2CCW): 1gram

PACKAGE

2 x Clockwise 4-blade 31mm props
2 x Counter-clockwise 4-blade 31mm props

$3.50
$3.50


In Stock: Totally in stock right now

BetaFPV 31mm 4-blade Micro Whoop Propellers (1.0mm Shaft) Pink


Experienced pilots will have different preferences when it comes to the number of blades on whoop drone propellers.

However, the general consensus is that 4-blade props produce greater thrust at a small efficiency expense — making them perfect for those looking for that extra edge when racing.

These props are suitable for the brushless tiny micro quadcopter whoops and and fit the shafts of BetaFPV's 0603, 0703 and 0705 motors.

These props will not work with our coreless brushed motors - the shaft diameter opening is too large and props will not be securely affixed to those motors.

THE IMPORTANT STUFF

Product material: Plastic
Outer diameter: 31mm
Shaft diameter: 1mm
Height: 7.2mm
Weight (2CW+2CCW): 1gram

PACKAGE

2 x Clockwise 4-blade 31mm props
2 x Counter-clockwise 4-blade 31mm props

$3.50
$3.50


In Stock: Totally in stock right now

BetaFPV 31mm 4-blade Micro Whoop Propellers (1.0mm Shaft) White


Experienced pilots will have different preferences when it comes to the number of blades on whoop drone propellers.

However, the general consensus is that 4-blade props produce greater thrust at a small efficiency expense — making them perfect for those looking for that extra edge when racing.

These props are suitable for the brushless tiny micro quadcopter whoops and and fit the shafts of BetaFPV's 0603, 0703 and 0705 motors.

These props will not work with our coreless brushed motors - the shaft diameter opening is too large and props will not be securely affixed to those motors.

THE IMPORTANT STUFF

Product material: Plastic
Outer diameter: 31mm
Shaft diameter: 1mm
Height: 7.2mm
Weight (2CW+2CCW): 1gram

PACKAGE

2 x Clockwise 4-blade 31mm props
2 x Counter-clockwise 4-blade 31mm props

$3.50
$3.50


In Stock: Totally in stock right now

BetaFPV 31mm 4-blade Micro Whoop Propellers (1.0mm Shaft) Yellow


Experienced pilots will have different preferences when it comes to the number of blades on whoop drone propellers.

However, the general consensus is that 4-blade props produce greater thrust at a small efficiency expense — making them perfect for those looking for that extra edge when racing.

These props are suitable for the brushless tiny micro quadcopter whoops and and fit the shafts of BetaFPV's 0603, 0703 and 0705 motors.

These props will not work with our coreless brushed motors - the shaft diameter opening is too large and props will not be securely affixed to those motors.

THE IMPORTANT STUFF

Product material: Plastic
Outer diameter: 31mm
Shaft diameter: 1mm
Height: 7.2mm
Weight (2CW+2CCW): 1gram

PACKAGE

2 x Clockwise 4-blade 31mm props
2 x Counter-clockwise 4-blade 31mm props

$3.50
$3.50


In Stock: Totally in stock right now

BetaFPV F3 FC with OSD (FrSky)


BetaFPV FC with F3 chip, embedded OSD and FrSky or DSM Rx (SBUS)
fits Whoop frames with 26x26mm mounting pattern

This flight controller is part of our Whoop kits.
To use the on-screen-display, use the VM2751 cam/vTx.

build instructions:

specifications:
CPU: STM32F303CCT6
sensor unit: MPU6000
ESC: 6.3A rated MOSFETs
dimensions: 26mm x 26mm
OSD: integrated BetaFlight OSD
receiver: Frsky D8 or DSM (SBUS)
power Cable: 55mm, with JST-PH 2.0 connector
weight: 3.4g

binding: press button on FC, then apply power. Now put transmitter into bind mode. Wait a few seconds, exit bind mode on Tx, then power cycle the FC.

The FC comes pre-flashed with BF 3.1.7. I recommend to update your board to the latest stable version BetaFlight 3.2. Here is a video about flashing and configuring BetaFlight:

$49.00
$49.00


In Stock: Sorry bro, Sold out

BetaFPV F4 1-2S AIO Brushless Flight Controller


This AIO F4 FC is suitable for a lighter 2S whoop drone, like Beta65 Pro 2 or Beta75 Pro 2 etc. It integrated a Betaflight F411 processor FC, Betaflight OSD, SPI Frsky receiver and 1-2S 5A ESC. So the 2S drone could save many weight for a faster fly experience.

SPECIFICATIONS OF FC

CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
Size: 26mm x 26mm, fully compatible with the all whoop drone mounting pattern, recommend the Beta65X frame and Beta75 Pro frame.
Firmware version: betaflight_matekf411rx_4.0.0 (Development Version)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Built in SPI Frsky D16 protocol native receiver, compatible with almost ALL Frsky FCC radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module. Not compatible with Frsky LBT protocol.
Power Cable: 55mm, with 2pcs JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 4.5g

DIAGRAM FOR F4 2S AIO FC (BUILT-IN FRSKY RX)

SPECIFICATIONS OF ESC

Built-in ESC with 5A continuous and peak 6A current
Power supply: 1-2S
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM

Status LED

There are 3 LEDs on the bottom of the board to indicate the status, including Receiver LED ( Green), FC Status LED ( Red ) and FC Power LED ( Blue ).

PACKAGE

1 * F4 2S brushless flight controller
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers

$60.00
$60.00


In Stock: Totally in stock right now

BetaFPV FC Screws and Damper pack


Those screws and rubber dampers are really useful when you are mounting flight controller board to your Blade Inductrix or Tiny Whoop Quadcopters. M1.2* 4 screws fit for stock Blade Indcutrix frame. M1.4* 5 screws fit for Eachine black E010 frame or Beta75 75mm frame.

PACKAGE
20 * M1.2* 4 screws
20 * M1.4* 5 screws
20 * ruber dampers

$11.50
$11.50


In Stock: Totally in stock right now

BetaFPV Sleek Frame and Canopy Combo Flame


This is a sleek looking combo of the frame and canopy for the Beta 65s.

SPECIFICATION

Frame base: 65mm wheelbase distance
Frame motor holder: 7x16mm coreless motors
Frame Color: Flame / Evil / Graffiti / Galaxy

PACKAGE

Durable plastic package can protect the frame from deformation during delivery process.
1* Combo of Sleek Frame and Canopy for Beta65S

$15.00
$15.00


In Stock: Totally in stock right now

BetaFPV Sleek Frame and Canopy Combo Flame


This is a sleek looking combo of the frame and canopy for the Beta 65s.

SPECIFICATION

Frame base: 65mm wheelbase distance
Frame motor holder: 7x16mm coreless motors
Frame Color: Flame / Evil / Graffiti / Galaxy

PACKAGE

Durable plastic package can protect the frame from deformation during delivery process.
1* Combo of Sleek Frame and Canopy for Beta65S

$15.00
$15.00


In Stock: Totally in stock right now

BetaFPV Sleek Frame and Canopy Combo Galaxy


This is a sleek looking combo of the frame and canopy for the Beta 65s.

SPECIFICATION

Frame base: 65mm wheelbase distance
Frame motor holder: 7x16mm coreless motors
Frame Color: Flame / Evil / Graffiti / Galaxy

PACKAGE

Durable plastic package can protect the frame from deformation during delivery process.
1* Combo of Sleek Frame and Canopy for Beta65S

$15.00
$15.00


In Stock: Totally in stock right now

BetaFPV Sleek Frame and Canopy Combo Graffiti


This is a sleek looking combo of the frame and canopy for the Beta 65s.

SPECIFICATION

Frame base: 65mm wheelbase distance
Frame motor holder: 7x16mm coreless motors
Frame Color: Flame / Evil / Graffiti / Galaxy

PACKAGE

Durable plastic package can protect the frame from deformation during delivery process.
1* Combo of Sleek Frame and Canopy for Beta65S

$15.00
$15.00


In Stock: Totally in stock right now

BetaFPV Tiny Whoop Canopy Black


No more broken cameras and video transmitters.

This super light white plastic canopy is low enough to allow the ability to precision hit small slots or gaps.

It supports the camera securely and eliminates tearing of SMD components on the board with aggressive double sided tapes.

All stock hardware is used for a super simple installation.

Unleash the your dark side!

This is the lightweight protective canopy you need for your whoop.

$3.00
$3.00


In Stock: Totally in stock right now

BetaFPV Tiny Whoop Canopy Blue


No more broken cameras and video transmitters.

This super light white plastic canopy is low enough to allow the ability to precision hit small slots or gaps.

It supports the camera securely and eliminates tearing of SMD components on the board with aggressive double sided tapes.

All stock hardware is used for a super simple installation.

This is the lightweight protective canopy you need for your whoop.

$3.00
$3.00


In Stock: Totally in stock right now

BetaFPV Tiny Whoop Canopy Clear


No more broken cameras and video transmitters.

This super light white plastic canopy is low enough to allow the ability to precision hit small slots or gaps.

It supports the camera securely and eliminates tearing of SMD components on the board with aggressive double sided tapes.

All stock hardware is used for a super simple installation.

This is the lightweight protective canopy you need for your whoop.

$3.00
$3.00


In Stock: Totally in stock right now

BetaFPV Tiny Whoop Canopy White


No more broken cameras and video transmitters.

This super light white plastic canopy is low enough to allow the ability to precision hit small slots or gaps.

It supports the camera securely and eliminates tearing of SMD components on the board with aggressive double sided tapes.

All stock hardware is used for a super simple installation.

Got a creative side? Here's your blank canvas - ready for paint, markers, stickers and whatever else!

This is the lightweight protective canopy you need for your whoop.

$3.00
$3.00


In Stock: Totally in stock right now

BetaFPV Tiny Whoop Sleek Canopy Chameleon


No more broken cameras and video transmitters.

This super light plastic canopy is low enough to allow the ability to precision hit small slots or gaps.

It supports the camera securely and eliminates tearing of SMD components on the board with aggressive double sided tapes.

All stock hardware is used for a super simple installation.

This is the lightweight protective canopy you need for your whoop.

*** Note: These are truly unique - no two canopies are exactly the same - print positioning will vary across all canopy styles

$7.00
$7.00


In Stock: Totally in stock right now

BetaFPV Tiny Whoop Sleek Canopy Dream


No more broken cameras and video transmitters.

This super light plastic canopy is low enough to allow the ability to precision hit small slots or gaps.

It supports the camera securely and eliminates tearing of SMD components on the board with aggressive double sided tapes.

All stock hardware is used for a super simple installation.

This is the lightweight protective canopy you need for your whoop.

*** Note: These are truly unique - no two canopies are exactly the same - print positioning will vary across all canopy styles

$7.00
$7.00


In Stock: Totally in stock right now

BetaFPV Tiny Whoop Sleek Canopy Evil


No more broken cameras and video transmitters.

This super light plastic canopy is low enough to allow the ability to precision hit small slots or gaps.

It supports the camera securely and eliminates tearing of SMD components on the board with aggressive double sided tapes.

All stock hardware is used for a super simple installation.

This is the lightweight protective canopy you need for your whoop.

*** Note: These are truly unique - no two canopies are exactly the same - print positioning will vary across all canopy styles

$7.00
$7.00

BetaFPV Tiny Whoop Sleek Canopy Flame


No more broken cameras and video transmitters.

This super light plastic canopy is low enough to allow the ability to precision hit small slots or gaps.

It supports the camera securely and eliminates tearing of SMD components on the board with aggressive double sided tapes.

All stock hardware is used for a super simple installation.

This is the lightweight protective canopy you need for your whoop.

*** Note: These are truly unique - no two canopies are exactly the same - print positioning will vary across all canopy styles

$7.00
$7.00


In Stock: Totally in stock right now

BetaFPV Tiny Whoop Sleek Canopy Galaxy


No more broken cameras and video transmitters.

This super light plastic canopy is low enough to allow the ability to precision hit small slots or gaps.

It supports the camera securely and eliminates tearing of SMD components on the board with aggressive double sided tapes.

All stock hardware is used for a super simple installation.

This is the lightweight protective canopy you need for your whoop.

*** Note: These are truly unique - no two canopies are exactly the same - print positioning will vary across all canopy styles

$7.00
$7.00


In Stock: Totally in stock right now

BetaFPV Tiny Whoop Sleek Canopy Skeleton


No more broken cameras and video transmitters.

This super light plastic canopy is low enough to allow the ability to precision hit small slots or gaps.

It supports the camera securely and eliminates tearing of SMD components on the board with aggressive double sided tapes.

All stock hardware is used for a super simple installation.

This is the lightweight protective canopy you need for your whoop.

*** Note: These are truly unique - no two canopies are exactly the same - print positioning will vary across all canopy styles

$7.00
$7.00


In Stock: Totally in stock right now

BetaFPV Upgraded Beta65 Pro Micro Brushless Whoop Frame


This is the upgraded and latest Brushless Whoop frame from BetaFPV.

Here's a picture showing you the differences between the previous versions:

This is designed for 0603 motors. Whilst you can run the 0703 motors if you really had to... don't do it, its inefficient and bad juju.

$6.00
$6.00


In Stock: Totally in stock right now

BetaFPV Z02 AIO Camera 5.8G VTX


This is the pin connected version. Although realistically, you can easily just cut/de-solder the pins and replace with wires if you wanted. You'll be right. It comes with a white TPU printed mount for the camera and vtx, works nicely.

Z02 AIO camera VTX is the newest video transmitter by BETAFPV. It has 2 great improvement since. First, switchable power output between 0mW, 25mW and 200mW. Second, Smart Audio is included and pilots could control the VTX via your radio transmitter.

FEATURE
Switchable power includes 0mW, 25mW and 200mW.
Smart Audio function is included in this AIO Z02 camera. The flight controller can communicate with the video transmitter using the audio line in. It allows the flight controller to know what frequency the vtx is using, and to change it.
Fixed 20° tilt camera mount. At this angle the pilot can still see everything ahead in full-blown fast forward flight.
Dipole whip high sensitivity antenna

SPECIFICATION
Output power: 0mW, 25mW and 200mW (Adjustable)
Supply Voltage: 2.9-5.5V
Size : 27*17*14 mm
Weight: 4.7g
Antenna: Omnidirectional ANT
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
TV System: NTSC
Field of view: 100-120 degrees with 1/4 lens.
HOW TO CHANGE FREQUENCY & CHANNEL & POWER
Frequency group A~F selected still touch up to 2 secs
Channel ch1~ch8 selected with short touch.
Power switch with long touch up to 5 secs.

PACKAGE
1 * BETAFPV Z02 FPV Camera
1 * TPU Holder
2 * Head pins (Using to connect with newest BETAFPV FC boards)

$34.50
$34.50


In Stock: Totally in stock right now

BigdaddyFPV 1300mAh 4s 100c Lipo Battery Pack


BigdaddyFPV 1300mAh V2 4s 100c Lipo Battery Pack

Searching for a decent, high-quality li-po battery that won't break the wallet isn't easy in Australia.

Enter the BigdaddyFPV range of lithium polymer batteries.

V2 Now lighter, physically smaller and with more punch!

Featuring protective plates on top and bottom, high discharge rates and excellent build quality!

NOTE: Please do not choose expedited shipping unless you live in greater Sydney as batteries cannot be shipped by Air.

Specifications:

Capacity (mAh): 1300
Voltage (V): 14.8
Discharge Rate (C): 100
Charge Rate (C): 3c Max (1c reccomended for longevity)
Configuration: 4S1P
Net Weight (±10g): 149
Length (±5mm): 73
Width (±5mm): 34
Height (±5mm): 28
Connector Type: XT, 60
Wire Gauge: AWG12

Lipo Battery Safety

Batteries should NEVER be left unattended while charging.
Be absolutely sure that the Lithium Polymer charger settings are correct for the battery pack being charged – both voltage and current settings.
Lithium Polymer must be CHARGED and STORED in a fire-safe container like a Lipo Sack.
Do not charge batteries near flammable items or liquids.
Keep a dry fire extinguisher nearby or a large bucket of dry sand, which is a cheap and effective extinguisher.
Never charge inside an automobile even when parked.
KEEP BATTERIES AWAY from children and pets at ALL times.
Never discharge below 3.5V per cell as it may cause permanent damage and void warranty
Battery may explode if damaged or disposed of in fire
Never leave batteries inside a car on a hot day or any other place where temperature may exceed 140F / 60C.
Although environmentally friendly, lithium polymer cells must be FULLY discharged before disposal. Use a resistor setup (light bulbs, for example) to accomplish this, to avoid the possibility of a short-induced fire after disposal.
Immediately discharge damaged batteries at 1/2 C rate and dispose
Do not put the loose cells in a pocket, bag, or drawer where they could short-circuit against other items, or the battery tabs could be pressed against each other.
Take care that the cells are not punctured, especially by metallic objects like hobby knives.
If the electrolyte in the cells should get on your skin, thoroughly wash with soap and water. If in the eyes, rinse thoroughly with cool water. Immediately seek medical attention for this, or for burns.

$28.95
$28.95


In Stock: Sorry bro, Sold out

BigdaddyFPV 1550mAh 4s 100c Lipo Battery Pack


BigdaddyFPV 1550mAh V2 4s 100c Lipo Battery Pack

Searching for a decent, high-quality li-po battery that won't break the wallet isn't easy in Australia.

Enter the BigdaddyFPV range of lithium polymer batteries.

V2 Now lighter, physically smaller and with more punch!

Featuring protective plates on top and bottom, high discharge rates and excellent build quality!

NOTE: Please do not choose expedited shipping unless you live in greater Sydney as batteries cannot be shipped by Air.

Specifications:

Capacity (mAh): 1550
Voltage (V): 14.8
Discharge Rate (C): 100
Charge Rate (C): 3c Max (1c reccomended for longevity)
Configuration: 4S1P
Net Weight (±10g): 180
Length (±5mm): 71
Width (±5mm): 35
Height (±5mm): 35
Connector Type: XT, 60
Wire Gauge: AWG12

Lipo Battery Safety

Batteries should NEVER be left unattended while charging.
Be absolutely sure that the Lithium Polymer charger settings are correct for the battery pack being charged – both voltage and current settings.
Lithium Polymer must be CHARGED and STORED in a fire-safe container like a Lipo Sack.
Do not charge batteries near flammable items or liquids.
Keep a dry fire extinguisher nearby or a large bucket of dry sand, which is a cheap and effective extinguisher.
Never charge inside an automobile even when parked.
KEEP BATTERIES AWAY from children and pets at ALL times.
Never discharge below 3.5V per cell as it may cause permanent damage and void warranty
Battery may explode if damaged or disposed of in fire
Never leave batteries inside a car on a hot day or any other place where temperature may exceed 140F / 60C.
Although environmentally friendly, lithium polymer cells must be FULLY discharged before disposal. Use a resistor setup (light bulbs, for example) to accomplish this, to avoid the possibility of a short-induced fire after disposal.
Immediately discharge damaged batteries at 1/2 C rate and dispose
Do not put the loose cells in a pocket, bag, or drawer where they could short-circuit against other items, or the battery tabs could be pressed against each other.
Take care that the cells are not punctured, especially by metallic objects like hobby knives.
If the electrolyte in the cells should get on your skin, thoroughly wash with soap and water. If in the eyes, rinse thoroughly with cool water. Immediately seek medical attention for this, or for burns.

$34.95
$34.95


In Stock: Totally in stock right now

Bind Plug


Replacement bind plug.

$2.50
$2.50


In Stock: Totally in stock right now

BK Servo Mini Gear Set for DS-5001HV & DS-7005HV


Includes:

- DS-5001HV and DS-7005HV Servo Gear x 1 set

Use for:

- DS-5001HV and DS-7005HV servos.

$27.90
$27.90


In Stock: Totally in stock right now

BOLT 2206W 2350kv WORX Motor


The BOLT WORX motors come with the same high performance stable as the Kraken WORX. Like all our WORX gear, it is designed from the ground up with our WORX race team to push boundaries and win races. WORX gear blends top performance, extreme light weight yet remain relatively durable for both training and race day.

These motors are designed to deliver a noticeable improvement in handling whilst still maintaining equivalent thrust with the leading power motors.

The motor uses thick N52H magnets and 0.15mm stator lamination that delivers outstanding power and performance. Wound with thick 0.5mm single strand copper, these are not cheap motors, despite the price. The motors uses higher quality ABEC 5 bearings from EZO. These bearings are unique to our WORX brushless motors delivering a more robust and lower profile motor for improved balance when placing the battery below the quad.

This combined with a light weight 25.8 grams (3cm wires) gives this motor an outstanding race pedigree. and most importantly, exceptional handling.

The motor uses a 19mm mount pattern.

Whats the big deal with the weight?

Actually, weight on the end of the arms is more important than any other location on the quad. Our race pilots report noticeable improvements in handling. Any weight here is just magnified by the arm length squared, just google 'moment of inertia'.

How durable are these motors?

Durable enough for both training and race day. We make extensive use of advanced FEA simulation tools to design our motors to maximize strength and yet still reduce weight. That said, nothing in the world is for free.....ie. not to be used for proximity flying.

2 Mount Holes?

Our WORX frames have only two mount holes on the arms.

There are no big fan blades on the cap to keep the motor cool?

Light weight 'fan blades' are hidden under the bell cap together with large exit area at the base make these motors extremely well ventilated.

Can I Run 6S

No, the stator will saturate and you are at risk of blowing the magnets. Its warranted only for 4S although 5S is is just fine, at your risk though.

What is the Thrust

Static thrust is around 1250-1275 grams with DAL 5045 v2s. Note that you can get slightly higher thrust with motors like the ZMX Fusion 2206, however, this comes at the expense of several grams of weight (thicker magnets and also requiring a thicker can). Our extensive race track testing shows that that the small incremental thrust delivers slower times due to poor handling characteristics.

Furthermore, the lighter WORX bell assists the motor accelerate to top speed even quicker.

$18.00
$18.00


In Stock: Totally in stock right now

BOLT Anti-Vibration Motor Mounts


Anti-vibration motor mounts for 2204 to 2208 size motors with 16mm to 19mm mount pattern.

These are made from high quality die cut silicone rubber with a 60 shore.

The mounts have an adhesive option to keep them firmly in place or to double up the thickness as required.

The pack has 10 mounts, enough for 2 quads with spares. Alternatively, stick two together for 2mm thickness.

$5.50
$5.50


In Stock: Totally in stock right now

BoltRC Kraken 3


The Kraken 3 is a ultra light weight and tough quad which leverages on the race wining design features of its big brother. The Kraken frames were created in collaboration with our top team pilots with the goal of producing an ultra competitive race winning performance.

Unlike almost 3in frames, the K3 features true symmetrical X design with superb flight characteristics and outstanding maneuverability. Coupled with our unique molded aerodynamic polycarbonate pod the Kraken 3 delivers a racing pedigree that is hard to match for speed, handling, weight and strength.

Key features include:

unique molded aerodynamic polycarbonate pod
3mm thick carbon fiber arms
not a unibody, it has replaceable arms
not a K frame, true symmetrical X design
fits full size FPV equipment including HS1177 camera

The frame build is quite simple when compared to other 3in frames. This reflects the unique pod design, custom pdb and integrated camera mount. This keeps your FC stack low with ample space for your electronics.

Typical frame weight is 35grams with build weights of approx 250 grams with 1407 motors.

The kit comprises of :
Kraken 3X Arms - 5pcs
Kraken 3 Bottom Plate - 1.5mm CF - 1pc
Kraken 3 PDB - 1.2mm Custom PDB with integrated 8v LDO regulator - 1pc
Kraken Hardware Pack - 1 pack
Kraken PC Pod - 1.0mm - 1pc
Kraken HS1177 Cam Bracket Kit - 1 pack
Kraken Battery Pad
Kraken PDB FC Inset Nuts - 5pcs

More Information:

For information on building your Kraken see link here

$72.00
$72.00


In Stock: Totally in stock right now

BoltRC Kraken 4


The Kraken 4 is an ultra light weight and tough quad which leverages on the race wining design features of its big brother, 5R. The Kraken frames were created in collaboration with our top team pilots with the goal of producing an ultra competitive race winning performance.

Kraken frames feature true symmetrical X design with superb flight characteristics and outstanding maneuverability. Coupled with our unique molded aerodynamic polycarbonate pod the Kraken 4 delivers a racing pedigree that is hard to match for speed, handling, weight and strength.

Key features include:

unique molded aerodynamic polycarbonate pod
4mm thick carbon fiber arms
not a unibody, it has replaceable arms
true symmetrical X design
fits full size FPV equipment including HS1177 camera

The frame build is quite simple when compared to other extreme X frames. This reflects the unique pod design, custom pdb and integrated camera mount. This keeps your FC stack low with ample space for your electronics.

The kit comprises of :
Kraken 4 Arms - 4pcs
Kraken 5 Bottom Plate - 1.5mm CF - 1pc
Kraken 5R PDB - 1.6mm Custom PDB with integrated 8v LDO regulator - 1pc
Kraken Hardware Pack - 1 pack
Kraken PC Pod - 1.5mm - 1pc
Kraken HS1177 Cam Bracket Kit - 1 pack
Kraken Battery Pad
Kraken PDB FC Inset Nuts - 5pcs

More Information:

For information on building your Kraken see link here

$85.00
$85.00


In Stock: Totally in stock right now

BoltRC Kraken 5 WORX


Note: This is the international version that ships with 2 pods but no LDO reg.

The K5W is an extreme light weight quad featuring aerodynamic performance. Despite weighing only 50 grams, the frame will survive a surprising number of tumbles. This is frame used by many of the worlds top pilots including rekrek, ghost, mad air, Julien FPV, waffle, jeddy, banni and many more!

Kraken frames feature true symmetrical X design with superb flight characteristics and outstanding maneuverability. Coupled with our unique molded aerodynamic polycarbonate pod the Kraken delivers a racing pedigree that is hard to match for speed, handling, weight and strength.

Key features include:

- unique molded aerodynamic polycarbonate pod
- 4mm thick carbon fiber arms
- not a unibody, it has replaceable arms
- true symmetrical X design
- fits full size FPV equipment including HS1177 camera

The frame build is quite simple when compared to other extreme X frames. This reflects the unique pod design, custom pdb and integrated camera mount. This keeps your FC stack low with ample space for your electronics.

The kit comprises of :

Kraken 5W Arms - 5pcs
Kraken 5 WORX Bottom Plate - 1.5mm CF - 1pc
Kraken 5 WORX PDB - 1.2mm Custom PDB with integrated 8v LDO regulator - 1pc
Kraken Hardware Pack - 1 pack
Kraken PC Pod - 1.0mm - 1pc
Kraken PC Pod - 1.5mm - 1pc
Kraken HS1177 Cam Bracket Kit - 1 pack
Kraken Battery Pad
Kraken PDB FC Inset Nuts - 5pcs

Warning - This is an extreme frame which requires occasional repairs due to higher breakage rate. Not recommended for beginners or proximity flying.

More Information:

For information on building your Kraken see link

$89.00
$89.00


In Stock: Totally in stock right now

BoltRC Kraken 5X


The Kraken 5 is an ultra light weight and tough quad which is designed and made to win races. The Kraken frames were created in collaboration with our top team pilots with the goal of producing an ultra competitive race winning performance.

Kraken frames feature true symmetrical X design with superb flight characteristics and outstanding maneuverability. Coupled with our unique molded aerodynamic polycarbonate pod the Kraken 4 delivers a racing pedigree that is hard to match for speed, handling, weight and strength.

Key features include:

unique molded aerodynamic polycarbonate pod
4mm thick carbon fiber arms
not a unibody, it has replaceable arms
true symmetrical X design
fits full size FPV equipment including HS1177 camera

The frame build is quite simple when compared to other extreme X frames. This reflects the unique pod design, custom pdb and integrated camera mount. This keeps your FC stack low with ample space for your electronics.

The kit comprises of :

Kraken 5X Arms - 4pcs
Kraken 5 Bottom Plate - 1.5mm CF - 1pc
Kraken 5X PDB - 2.0mm Custom PDB with integrated 8v LDO regulator - 1pc
Kraken Hardware Pack - 1 pack
Kraken PC Pod - 3.0mm - 1pc
Kraken HS1177 Cam Bracket Kit - 1 pack
Kraken Battery Pad
Kraken PDB FC Inset Nuts - 5pcs

The K5R is built lighter whereas the K5X is built tougher:

K5R has a 1.6mm PDB whereas K5X has a stronger stiffer 2.0mm PDB
K5R arms are 12mm wide at narrowest point whereas K5X is 14mm
K5R uses the 2.0mm pod whereas the K5X uses the 3.0mm pod.
More Information:

For information on building your Kraken see link here.

$89.00
$89.00


In Stock: Sorry bro, Sold out

BoltRC Lambda 5


This is the all new BoltRC Lambda 5 inch racing frame.

The frame is a semi stetch sitting half way between a symmetrical and full stretch. Also, the front and rear arms do not meet in the centre. Why you ask? You get most of the stretch flight benefits but none of the strength disadvantages. Essentially the arms are the same length as a regular symmetrical frame arm

Weight is approx 70g (TBC)

5mm thick custom foam sandwich arms.
Hybrid motor mount system for great strength on front arms
Fits mini cams with 4 point adj mount
Lens Check (cam bracket slides forward and aft by 3mm)
Thick 2mm top plate for strength
1mm integrated top front bumper
30mm 7045 standoffs
Rear 7075 multi purpose standoff
Integrated XT60 clamp
Integrated VTX antenna mount - regular
Compatible with unify and tramp antenna mount
Integrated 30.5 and 20x20 FC stack systemThe kit comprises of :

Front Arms - 2pcs
Rear Arms - 2pcs
Lower Bottom Plate - 2mm CF - 1pc
Upper Bottom Plate - 1.5mm CF - 1pc
Top Plate - 2mm - 1pc
Top Front Bumper - 1mm - 1pc
Bottom Front Bumper - 5mm - 1pc
Bottom Rear Bumper - 5mm - 1pc
7075 Front Standoff - 3pcs
7075 Rear Standoff - 3pcs
Hardware Pack - 1 pack
Cam Brackets (L+R) - 1 each
Battery Pad

$80.00
$80.00


In Stock: Totally in stock right now

BrainFPV Radix LI Flight Controller


Graphics OSD

On top of the normal Betaflight OSD, RADIX LI on-screen-display gives you extra features you can't get anywhere else. Proudly show off your pilot and team logo using our logo customizer with just a click of a button. Extra features also include a graphical barometer scale, artificial horizon, gyro spectrograph, RC stick display, 3D OSD support and more!
Compared to the RADIX, the RADIX LI:

Is smaller (doh): 20mm hole spacing, 26.5mm x 26.5mm outside dimensions
Can be powered directly from a 3S - 6S LiPo battery (500mA BEC built-in)
Does not have a barometer (you can attach a GPS to it if you want to know how high you are)
Does not have a MicroSD card slot (who need blackbox if you can OSD spectrograph for tuning?)
Does not have an analog RSSI input (these days, using RSSI or LQ over an RC channel is more common and more accurate)
Finally: The RADIX LI is cuter

FC Specification

Processor: STM32F446RET6, Coretx-M4, 32bit, 180MHz, 128kB RAM, 512kB Flash.
IMU: Bosch Sensortec BMI160 running at 3.2kHz, connected using SPI.
OSD: Full-graphic, PAL/NTSC auto detect, adjustable black and white levels. Full Betaflight OSD support with extra graphical features. Support for side-by-side 3D when used with a 3D FPV camera.
Motor Outputs: 6 outputs with full DSHOT (150/300/600/1200) and OneShot support.
Receiver Support: PPM, S.Bus (inverter built-in), DSM, HoTT, SRXL, CSRF, FPort ready. 5V or 3.3V supply for receiver. Receiver is powered from USB for easy and safe setup.
Telemetry Support: FrSKY Smart Port, FrSKY Sensor Hub, HoTT Telemetry, SRXL, CSRF, FPort ready. Built-in inverter for FrSKY telemetry.
Serial Ports: 4 full serial ports (UARTs). UART3 and UART6 have inverters for S.Bus and SmartPort telemetry. Inverters are automatically enabled/disabled for maximum flexibility.
RGB LEDs: Dedicated RGB LED output.
Camera Control: Dedicated output for accessing the camera menu to change camera settings.
Buzzer Port: Dedicated port for 5V (100mA max) buzzers.
Analog Inputs: Voltage sensing (VBAT), current input (3.3V max).
Power: 3S - 6S (7.5V - 26V), 500mA BEC
Dimensions: 26.5mm x 26.5mm, 20mm hole spacing. 4.1mm holes for anti-vibration grommets for M3 screws.
Weight: 4g
Gluten free, Non GMO, Free Range Anorganic Gyro

RADIX LI Includes

RADIX LI flight controller
Silicone anti-vibration grommets 4x
BrainFPV 4-in-1 ESC cable kit (cables and connectors to make a cable that works with any 4-in-1 ESC with a JST-SH 7 pin, 8 pin, or 10 pin connector)

$84.90
$84.90


In Stock: Totally in stock right now

BRIX Race 5 Inch - Pod X Frame


The BRIX Race is the perfect companion for your BRIX Trainer (available here). The BRIX Race is faster, lighter, more streamlined and cooler than the trainer version. Practice on the BRIX Trainer, and pull out the BRIX Race on race day.

The BRIX Race is built for 5" props and weighs less than 85 grams including fasteners. The arms are made out of the highest grade full twill 4mm carbon fibre and feature a near unbreakable polyurethane pod resulting in an incredibly tough 5 inch X frame.

Each frame includes a red 55 degree TPU pod, 2x battery straps, a fastener kit, bottom plate, top plate and a custom PDB designed with the FMR Kakute in mind.

The pod is designed for HS1177 form factor cameras and the AU799T VTX or similar.

$77.00
$77.00


In Stock: Totally in stock right now

Bullet Connectors 6mm Gold


6mm Sprung Gold Connectors. Nice and beefy.

Good to around 160A

Includes 1 pair.

$1.20
$1.20


In Stock: Sorry bro, Sold out

Bullet Connectors 8mm Gold


8mm Gold Connectors
Rated to around 170A
Excellent for high current systems.
Includes 1 pair
Weight: 11g (per pair)

$2.50
$2.50


In Stock: Totally in stock right now

Byron Originals Lube Booster


This is a 10 ounce bottle of Byron Originals Lube Booster. Lube Booster was designed as a response to requests from modelers currently running non-Byron fuel of questionable oil content and oil quality. Lube Booster can be added in an effort to "upgrade" the "Brand X" fuel in some cases where a higher oil content may be desired for break-in of certain engines. Lube Booster also allows the modeler to mix his own break-in fuel in the quantity and nitro content he or she wants.

$15.00
$15.00


In Stock: Totally in stock right now

CL-0615-17 Red Edition Coreless Motor (speed: faster) 4 Pack


A great all-round motor for serious whooping, with good power and good efficiency!

Warning: do not use this motor with the Nano QX (non FPV), Nano QX FPV or Inductrix (non FPV) FCs. The motors are too fast for these FCs and will cause throttle and oscillation issues.

Its OK to use the 0615-17 motors with the Inductrix FPV FC.

17.000Kv: very fast, a noticeable boost over the -14 motors, but not as power-hungry as the -19s

performance data:

speed: 17.000Kv
operating voltage: 1.5-3.7V
1.5A load current at 3.7V (direct drive)
lifetime rating: 5-6 hours
dimensions:

can diameter: 6mm
can length: 15mm
shaft diameter: 0.8mm
shaft length: 5mm
weight: 1.8g
wire length: 70mm
plug: Micro-JST-1.25
To maximize performance and life span, don't run them in reverse!

Motor rotation and correct polarity is indicated by the wire color:
clockwise: red +, blue -
counter clockwise: white +, black -

Please note: wire color coding is reversed from the stock motors. (Blade has decided to code their motors differently to everyone else in the industry..) Please click here for installation instructions! (Inductrix and Nano QX have the same motor positions)

$25.00
$25.00


In Stock: Totally in stock right now