Based on the idea of BadAssDrones, Drone Junkie created an extremely thought-out micro hover craft kit that uses the electronics of a micro quad as control and propulsion system.

kit contents:
2x foam sheets with body parts
2x 3D-printed motors mounts
1x bottom skid pad

required, but not included:
- whoop frame, motors, propellers (recommended: 7016 body kit)
- flight controller (any whoop FC will do, but a programmable one is best)
- batteries (anything between 200mAh and 600mAh works)

Based on the idea of BadAssDrones, Drone Junkie created an extremely thought-out micro hover craft kit that uses the electronics of a micro quad as control and propulsion system.

kit contents:
2x foam sheets with body parts
2x 3D-printed motors mounts
1x bottom skid pad

required, but not included:
- whoop frame, motors, propellers (recommended: 7016 body kit)
- flight controller (any whoop FC will do, but a programmable one is best)
- batteries (anything between 200mAh and 600mAh works)

The TinySnapper offers a very simple way of controlling your digital camera from your RC system and it’s really affordable.

Just plug in the TinySnapper where you normally plug in a servo motor – when you flip the switch on your remote, the TinySnapper will trigger your camera via an infrared transmitter.

I doesn’t get any simpler! The TinySnapper is preprogrammed to work with a specific brand, and triggers the shutter when the servo signal is a bit above neutral.

Please remember that most cameras need to be setup to accept IR remote and you need to disable auto power-off.

Mounting is easy. The TinySnapper has a flexible neck which allows you to point the transmitter in the direction of the IR receiver on your camera. It also comes with some Dual Lock re-closeable fasteners for mounting.

The TinySnapper comes in many flavors! Currently all mayor camera brand are supported, but be sure to pick the type that suits you camera when ordering. The TinySnapper currently supports triggering of more than 100 camera types. Check out the supported cameras page.

Specifications:

Takes a standard servo input and converts it into an infrared remote camera trigger signal.
Accepts standard 5V servo power. (don’t push it beyond 6.5V).
Very low weight and form factor.
Flexible neck for precise positioning.
Dual Lock re-closeable fasteners included for easy mounting.
35 cm servo cable.
Ultra bright IR transmitter for reliable communication.
Lead free. RoHS compliant.
If you are looking for a more customizable solution check out the StratoSnapper

The TinySnapper offers a very simple way of controlling your digital camera from your RC system and it’s really affordable.

Just plug in the TinySnapper where you normally plug in a servo motor – when you flip the switch on your remote, the TinySnapper will trigger your camera via an infrared transmitter.

I doesn’t get any simpler! The TinySnapper is preprogrammed to work with a specific brand, and triggers the shutter when the servo signal is a bit above neutral.

Please remember that most cameras need to be setup to accept IR remote and you need to disable auto power-off.

Mounting is easy. The TinySnapper has a flexible neck which allows you to point the transmitter in the direction of the IR receiver on your camera. It also comes with some Dual Lock re-closeable fasteners for mounting.

The TinySnapper comes in many flavors! Currently all mayor camera brand are supported, but be sure to pick the type that suits you camera when ordering. The TinySnapper currently supports triggering of more than 100 camera types. Check out the supported cameras page.

Specifications:

Takes a standard servo input and converts it into an infrared remote camera trigger signal.
Accepts standard 5V servo power. (don’t push it beyond 6.5V).
Very low weight and form factor.
Flexible neck for precise positioning.
Dual Lock re-closeable fasteners included for easy mounting.
35 cm servo cable.
Ultra bright IR transmitter for reliable communication.
Lead free. RoHS compliant.
If you are looking for a more customizable solution check out the StratoSnapper

High quality transmitter knobs offer more precise control and feel. Produced from lightweight aluminum and black anodized to assure long lasting performance.

Knurled on sides and recessed on top for better feel.

These Dampeners are made from a new Super Hard Green material. These are by far the hardest most durable Dampeners available to date!

Should your product come with any molding flash:

1. Poke a small hole in the flash with an X-Acto blade.
2. Push the spindle through the damper stretching the flash onto the spindle.
3. Take the X-Acto blade and cut around the spindle next to the damper.

T-Rex 250 Swash Plate Leveler
This is the original Trueblood Swashplate Leveler by Trueblood Engineering. Proudly Made in the USA.

Bench User Guide

Compatible Helicopters

Click here for more information

Vibe 50 Swash Plate Leveler
This is the original Trueblood Swashplate Leveler by Trueblood Engineering. Proudly Made in the USA.

Bench User Guide

Compatible Helicopters

Click here for more information

The TS100 Digital OLED Programmable Soldering Iron is an internal heating intelligent CNC soldering iron. It is easy to assemble and disassemble for storage and portability. It has a comfortable handle and the highly effective heating function makes it an indispensable tools for any hobbyist. It is made from high quality metal & plastic materials and assembled with great workmanship, for high durability and reliability.

Our favourite feature of the TS100 is it's ability to be so mobile. It can easily be powered by a 4s lipo battery while on the go, no A/C outlet required. This means you can make quick fixes while out at the field. The iron heats up to operating temperature in under 15 seconds! This is a must have for any RC enthusiast.

Features

Built-in acceleration sensors with STM32 chip can intelligently record your usage habits
Bright OLED screen is clear easy for you to read information
Digital temperature readout
Temperature control button is set on the handle allowing for easy temperature adjustments
Anti-static structure with ground wire ensures your safety during use
Supports custom programmable development (Micro USB Connection)
Multiple soldering head types are available (Up to 7)
Can be powered via a 3-4s LiPo battery for mobile use

Specifications

Model TS100
Material Metal & Plastic
Power 65W
Special Function Programmable, Temperature Adjustment
Voltage(V) 12-24V
Temperature Control Support Yes
Adjustable Temperature Range 100 Centigrade - 400 Centigrade
Heating Type Internal Heating
Working Temperature 300 Centigrade
Color Black
Dimensions (6.61 x 0.67 x 0.51)" / (16.8 x 1.7 x 1.3)cm (L x W x H)
Weight 0.74oz / 21g

Package Includes

1 x TS100 Digital LCD Soldering Iron
1 x TS-I Solder Tip (please note not all product pictures depict this - please see chart)
1 x Allen Wrench
2x Extra Locking Screws
1 x Bilingual Manual in English and Chinese

Power your TS-100 soldering iron easily from an XT60 battery using this handy XT-60 to 2.5mm DC jack cable - designed specifically for the TS-100.

Please Note: Actual product may differ slightly from product picture.

High strength and light weight.

The 4pc TURNIGY hex socket driver set includes sizes 4.0B, 4.5B, 5.5B and 7.0B.

Made from high strength tool steel, these tools reduce rounding and ensure a secure screw fit each time.

Turnigy High Density light strips come with 60 LEDs per meter!!
LEDs are arranged in sets of 3, you can cut the strip and make new strips or extend strips to make any combination of 3 lights!

Features:
Comes with adhesive tape backing for easy mounting
Flexible enough to be bent at any angle
Easy to use. Just peel and stick!
Large voltage input range up to 12V DC! (Great for 2-3S Lipoly)

Specifications:
Standard length: 1 meter
Strip width: 8mm
LED quantity per strip(1 mtr): 60 LEDs
Working voltage: DC12V
Working current(1mtr): 400mA
Wire length(1mtr): 10cm
Weight including wire(1mtr): 11g

Turnigy High Density light strips come with 60 LEDs per meter!!
LEDs are arranged in sets of 3, you can cut the strip and make new strips or extend strips to make any combination of 3 lights!

Features:
Comes with adhesive tape backing for easy mounting
Flexible enough to be bent at any angle
Easy to use. Just peel and stick!
Large voltage input range up to 12V DC! (Great for 2-3S Lipoly)

Specifications:
Standard length: 1 meter
Strip width: 8mm
LED quantity per strip(1 mtr): 60 LEDs
Working voltage: DC12V
Working current(1mtr): 400mA
Wire length(1mtr): 10cm
Weight including wire(1mtr): 11g

Turnigy High Density light strips come with 60 LEDs per meter!!
LEDs are arranged in sets of 3, you can cut the strip and make new strips or extend strips to make any combination of 3 lights!

Features:
Comes with adhesive tape backing for easy mounting
Flexible enough to be bent at any angle
Easy to use. Just peel and stick!
Large voltage input range up to 12V DC! (Great for 2-3S Lipoly)

Specifications:
Standard length: 1 meter
Strip width: 8mm
LED quantity per strip(1 mtr): 60 LEDs
Working voltage: DC12V
Working current(1mtr): 400mA
Wire length(1mtr): 10cm
Weight including wire(1mtr): 11g

Turnigy High Density light strips come with 60 LEDs per meter!!
LEDs are arranged in sets of 3, you can cut the strip and make new strips or extend strips to make any combination of 3 lights!

Features:
Comes with adhesive tape backing for easy mounting
Flexible enough to be bent at any angle
Easy to use. Just peel and stick!
Large voltage input range up to 12V DC! (Great for 2-3S Lipoly)

Specifications:
Standard length: 1 meter
Strip width: 8mm
LED quantity per strip(1 mtr): 60 LEDs
Working voltage: DC12V
Working current(1mtr): 400mA
Wire length(1mtr): 10cm
Weight including wire(1mtr): 11g

Made from high-temp Nylon and gold plated spring connectors, both included in the injection mould at the time when forming the connector. The XT60 ensures a solid high-amp connection, perfect for applications up to and beyond 65A constant.

micro cam/vTx, 5.8G 40CH 25mW, 3.6g
For a compatible camera mount, click here.
For a complete Whoop Brain kit, click here.

sample video (recorded over ClearView receiver and Eachine ProDVR):

- weight: 3.6g
- dimensions: 47x15x12.5mm
- PAL/NTSC switchable (long press front button)
- image invert (short press front button)
- channel selection (short press back button)
- band selection (long press back button)

- output power: 25mW
- supply Voltage: 2.9-5.5v
- power consumption: 200mA @ 5V
- lens angle: horizontal:120°/vertical:100°

Temperature sensor plugs into your Voltz charger and is intended to monitor your batteries while charging.

The Nano-Nano board was designed to allow you to mount your Team BlackSheep Unify Pro Nano VTX in your stack for cleaner builds. This board includes holes that are compatible with (but not limited to) most receivers such as the FrSky XM+ and Team BlackSheep Crossfire Nano. Once the VTX is soldered into the cutout on the board, the breakout pads on the side allow for full access to your VTX.

If your camera uses 5V for power, you can solder your pigtail to the camera pads and allow the board to act as a pass through. After your VTX, camera, and receiver is installed, the 5V pad on the board will power all your components.

There are also two pads located on the side of the board to solder the button that's included with your Unify Nano. The button can be soldered top facing, side facing, or with wires to allow for access to the VTX from anywhere.

Note: If your receiver requires 3V, you will need to pull power from somewhere else. Do not solder in the 5V header if your receiver is not compatible. You can use the other plated through holes (1, 2, and ground) for your receiver still.

FEATURES
TBS Unify Pro Nano Video Transmitter support
4 plated through holes for mounting receivers
Pads for camera pigtail
Top or side pads for VTX button
20mm x 20mm hole pattern
27mm x 26mm dimensions

Wire Mesh Guard is an excellent way to protect servo leads or battery wires.

This is the NEW XeroGear Night Fly System. This kit is appropriate for a 500/50 sized electric helicopter. The XeroGear Night Fly System is made of bright LED's mounted on flexible tape that has 3M brand adhesive backing. The LEDs emit a bright vibrant light available in Red, Blue, Green and Amber. We have even included Landing Light to make landing at night easy and worry free. Once you use the XeroGear Night Fly System you will never want to use anything else.

Features:
- Superior visibility
- Brighter more vibrant colors
- Ability to fly at Dusk with perfect visibility
- EASY landing! We have included a Landing Light!
- Orientation like you never thought possible
- NO controller needed!! simply plug into a 7-12 volt power source
- Extremely light weight
- Low power consumption - 6 feet of LEDs draws .05 Amp using a 2s 7.4v Lipo
- Ability to CHANGE the BRIGHTNESS of the LEDs
- Use the optional Light Controller for complete control of your lights from your transmitter - Dim, Brighten, and turn off
- Use a 3s lipo or any 12v power source for full brightness - allows the lights to be visible in bright sunlight and dusk
- Use a 2s lipo to fly with the LEDs dim for full night flight and dark conditions
- Flexible installation options - Simply cut the LED strip to length, peel the adhesive backing and stick on the surface or use zip ties and have the ability to reconfigure your lights when ever you want

1 x High quality replacement bearing set

(4 bearings)

Suits Xnova 2204 series motors

Replacement shaft for Xnova 2204 size motors

Package contains: 4 x 2204 Replacement Shafts

1 x High quality replacement bearing set

(4 bearings)

Suits Xnova 2206 series motors

Replacement shaft for all Xnova 2206 size motors

Package contains: 4 x 2206 Replacement Shafts

Xnova motors are made from the finest components available today and guaranteed for the highest levels of performance and efficiency. Each Xnova motor is 100% hand wound and guaranteed to perform. Be convinced by the results, not just datasheets.

High performance
Finest CNC quality
Ultimate efficiency
Low cogging torque
Smooth running
Precise balancing
Fully tested
100% hand wound
5″ to 6″ Prop Size

XT60 SmokeStopper - Termed the SmokeStopper by RCgroups member mnemennth, this handy device could save you from damaging expensive electronic components

We've all been there... Working all day on a new build, you finally finish, you give your new beast one final look-over and don't see anything wrong. So you plug it in and TZZZT! SNAPP! POP! and instantly, your plans for new-found aerial bliss disappear literally in a puff of smoke.

You tear it down and find a blown ESC caused by a motor with a too-long screw into a winding or a little blob of solder that you SHOULD have caught before you put the new shrink-wrap on, but DIDN'T.

Now you have to tear it apart and replace the toasted ESC before you can even see if the motor is salvageable. You already know you're going to be ordering a new one shortly; the only difference is whether you're going have to wait for it to come in the post or if you ordered enough to have a spare and will need to replace it.